홈페이지> 블로그> Car anti-theft system based on GPS and GSM network 2013-07-22 (1)

Car anti-theft system based on GPS and GSM network 2013-07-22 (1)

February 26, 2023

0 Preface

With the advent of the new era, the automobile has also developed rapidly as an important means of transportation. At the same time, the subsequent car theft has also increased. However, most of the car anti-theft systems on the market currently have certain limitations. Therefore, a network-based anti-theft system with high reliability and security has gradually entered the field of vision. Network-based anti-theft mainly breaks through the limitation of distance, solves the passive anti-theft method of traditional physical anti-theft device, integrates advanced GPS positioning system and GSM communication system module, and uses SMS (short message service) to send and receive text messages to the owner. Two-way communication between users. The interactive, active alarm mode not only informs the owner of the car before it is illegally moved, but also remotely controls the vehicle via the network. This project is a kind of intelligent anti-theft system for the public that is developed by GPS and GSM network and is more reliable and safe.

1 overall system design

The system is mainly composed of GSM module, GPS receiver module, single-chip control circuit, sensor alarm circuit and power supply circuit. The sensor alarm module monitors the abnormal condition of the vehicle; the GPS module is responsible for receiving the positioning data; the single chip control circuit collects, receives and analyzes the GPS positioning data under the condition that the abnormality is detected, and the GSM module sends and receives the short message under the control of the single chip; the power circuit 7805 is The MCU and GPS module provide +5V DC voltage, and the LM2941CS regulates the +5V DC voltage to +4.2V for use by the GSM module.

a.jpg

2 system hardware design

2.1 Sensor section

This system uses Hall switch, vibration sensor, tilt sensor and pyroelectric infrared sensor to monitor different aspects of vehicle body vibration, vehicle body position change and human biological information, and can obtain enough information for car anti-theft. Eliminate the uncertainty of information to the extent and improve the reliability of the alarm.

2.2 GSM part

This system adopts Siemens GSM module TC35i from Germany. The module is RS232 data port, dual frequency (GSM900/GSM1800), and complies with ETSI standards GSM0707 and GSM0705. It contains RF circuitry and baseband, and provides a standard AT command interface for bidirectional transfer of instructions and data, and fault recovery and restart via shutdown or AT commands. Its working voltage is 4.2V, and it will automatically shut down when the module's power supply voltage is lower than 3.3V. Because the module emits a signal with a current maximum of 2A, it is powered by a high-demand power supply. This system uses the voltage regulator chip LM2941CS, which is dedicated to the adjustable switch type high performance microwave circuit, which can provide stable high current and voltage output. The TC35i module pins can be divided into five categories: power supply, SIM card, data input/output, audio interface and control. When using the TC35i module, to put the TC35i into operation, ensure that its start pin IGT plus a low level longer than 100ms.

b.jpg

2.3 GPS section

This system uses SIRF third-generation high-sensitivity leaded GPS receiver module SIRF starIII. The chip is serial communication, baud rate 4800; level data output, format is TTL. With 20 channels, it can track 20 satellite channels at the same time, ensuring the highest receiving sensitivity and positioning accuracy less than 10m. There is a rechargeable battery inside, which can store ephemeris data for quick positioning. The data can be powered off for more than seven days. The module GPS uses a standard MMCX antenna interface for easy connection to a GPS antenna. The data line interface uses a 6-wire connector lead output to facilitate prototyping during product development, and is very simple to use, requiring only three output lines. The output of GPS uses the second pin, which is the serial port TTL level signal, the high level is greater than 2.4V, the low level is less than 0.4V, the output drive capability is 2mA, and can be directly interfaced with the single chip; Six feet, each output a pulse signal of about 0.2V with a width of 10ms for timing; the DC positive power supply is 3.5~5.5V, the first pin is used; the fifth pin is used for the power ground. By default, the GPS receiver module SIRF star III outputs positioning data once per second, usually in the $GPRMC streamlined data format. The statement format is as follows:

$GPRMC, <1>, <2>, <3>, <4>, <5>, <6>, <7>, <8>, <9>, <10>, <11>, <12>

*hh <10-12> is generally not used. Each positioning data starts with "$" and ends with a carriage return. 基于GPS和GSM网络的汽车防盗系统 2013-07-22 (1)2

[1] [2] 基于GPS和GSM网络的汽车防盗系统 2013-07-22 (1)3
문의하기

Author:

Ms. Zoe Zhong

Phone/WhatsApp:

+8618617178558

인기 상품
You may also like
Related Categories

이 업체에게 이메일로 보내기

제목:
휴대전화:
이메일:
메시지:

Your message must be betwwen 20-8000 characters

2010 년에 설립 된 Entnorson Antenna Co., Ltd는 커뮤니케이션 안테나의 연구, 개발, 판매 및 서비스에 종사하는 전문 회사입니다. Yetnorson은 2 g/3 g/4 g/wifi/TV 안테나와 다양한 RF 커넥터 및 안테나 케이블 어셈블리를 전문으로했습니다. 우리는 5 명의 엔지니어가있는 R & D 팀이 7 일 이내에 고객의 사양에 따라 프로젝트를 완료 할 수 있으며 귀하의 옵션을 위해 500 가지 이상의 현재 안테나 제품을 제공합니다. 그 동안 36 개의 제품 특허와 8 개의 상표가 있으며 ISO...
Newsletter
회사 주소
Room #101,201,301,5BLDG , No.4 of XinWuCun New Area ,Shabo community Maluan Street Pingshan District, Shenzhen ,Guangdong , China, Shenzhen, Guangdong China

Copyright © 2024 Yetnorson Antenna Co., Ltd.판권소유

Copyright © 2024 Yetnorson Antenna Co., Ltd.판권소유

We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

송신