홈페이지> 블로그> Antenna amplifier introduction and application

Antenna amplifier introduction and application

July 29, 2023
Murata muRata winding inductance original authentic assured purchase

About antenna amplifier

Antenna amplifiers are also called preamplifiers. They are commonly called Mastheader Amplifiers in English. Some European and American countries are called Pre-amplifier or Antenna Amplifier, AmplifICador, etc. They are ultra-high frequency, wideband, low noise amplifiers for antennas and feeders. It is used to enhance the weak signal caused by the receiving distance too far, compensate the loss of the transmission distance between the antenna and the TV, and ensure the necessary input power of the distributor in the shared antenna system to improve the receiving quality.

When we receive long-distance TV programs or accept high-definition TV programs on the ground, the TV signals are generally weak. In this case, we need to use a multi-unit TV antenna with strong directivity and high gain. We also need to set the antenna as high and empty as possible. The place. If the receiving situation is not ideal enough, an antenna amplifier should be added between the antenna and the TV to improve the receiving sensitivity and stabilize the image of the TV with good sound.

After using the antenna amplifier, it is like adding a "telescope" to the TV. It can zoom in on the weak TV signal received by the antenna, but of course, in the process of receiving, it is not only the TV signal, but also the Noise and interference. Usually the antenna signal can amplify the TV signal to a dozen times or more. The antenna amplifier is actually an oversized high-band amplifier. The receiver channels, frequency range, and overall gain of various antenna amplifiers are different.

When using an antenna amplifier, pay attention to the following issues.

(1) Note the installation position The antenna amplifier usually consists of an amplification part and a power supply. In the case of short antenna feeders (generally using indoor antennas), the antenna amplifier can be placed next to the TV; when the antenna is set high and the feeder is long, the two parts should be placed separately, and the enlarged part is sealed by a waterproof box. After that, it is preferable to be installed at the end of the support rod 1 to 1.5 m from the antenna element, and the power supply portion can be placed near the television, which can improve the signal-to-noise ratio of the television signal.

(2) The channel must match the antenna amplifier. It is divided into two categories: very high frequency and ultra high frequency. The VHF type can amplify TV signals of 1 to 12 channels, and the UHF type can amplify TV signals of 13 to 68 channels. When in use, the antenna amplifier should match the TV channel to be received.

(3) Note that the output impedance of the impedance matching antenna amplifier and the antenna output and the input impedance of the TV should match. The feeder should not be too long, that is, the antenna cannot be placed too high or too far. Otherwise, although an antenna amplifier is added to the television set, the increased signal is severely attenuated during transmission to the television set, resulting in little improvement in reception. In addition, the input and output feeders of the antenna amplifier must not overlap or be placed too close together to avoid feedback or interference.

(4) Must choose the gain of the antenna amplifier of various models is different, generally there are high and low points. High-gain antenna amplifiers typically have a gain of 30 to 60 dB and are compatible with multi-channel Yagi antennas to receive TV programs hundreds of kilometers away. The low-gain antenna amplifier has a gain of 20 to 4OdB and can receive programs dozens of kilometers away. Make the appropriate choices when choosing, but not the higher the gain, the better.

(5) Checking the installation effect If the image received by the indoor large line is inferior and the outdoor antenna can be used to obtain good results, the indoor antenna can still be used after the amplifier. If the viewing effect of the TV is not changed after the antenna amplifier is installed, or if the viewing effect is worse than before, it is caused by an installation error. It should be carefully checked and then corrected according to the correct installation method.

(6) There are good antennas and lightning protection equipment. For example, TV users who use outdoor antennas need to install antenna amplifiers. They must have good multi-unit antennas to cooperate with them, and lightning protection equipment should be installed to prevent lightning strikes.

The evaluation criteria of the antenna amplifier

a small signal noise

Second, the sensitivity is high

Three waterproof is better

Four volumes are smaller

Five metal casings are better

Six power saving

Seven wiring is convenient

문의하기

Author:

Ms. Zoe Zhong

Phone/WhatsApp:

+8618617178558

인기 상품
You may also like
Related Categories

이 업체에게 이메일로 보내기

제목:
이메일:
메시지:

Your message must be betwwen 20-8000 characters

2010 년에 설립 된 Entnorson Antenna Co., Ltd는 커뮤니케이션 안테나의 연구, 개발, 판매 및 서비스에 종사하는 전문 회사입니다. Yetnorson은 2 g/3 g/4 g/wifi/TV 안테나와 다양한 RF 커넥터 및 안테나 케이블 어셈블리를 전문으로했습니다. 우리는 5 명의 엔지니어가있는 R & D 팀이 7 일 이내에 고객의 사양에 따라 프로젝트를 완료 할 수 있으며 귀하의 옵션을 위해 500 가지 이상의 현재 안테나 제품을 제공합니다. 그 동안 36 개의 제품 특허와 8 개의 상표가 있으며 ISO...
Newsletter
회사 주소
Room #101,201,301,5BLDG , No.4 of XinWuCun New Area ,Shabo community Maluan Street Pingshan District, Shenzhen ,Guangdong , China, Shenzhen, Guangdong China

Copyright © 2024 Yetnorson Antenna Co., Ltd.판권소유

Copyright © 2024 Yetnorson Antenna Co., Ltd.판권소유

We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

송신