홈페이지> 블로그> 24GHz Microstrip Array Antenna Design Experience

24GHz Microstrip Array Antenna Design Experience

April 29, 2022
This paper mainly studies the design of the matching network applied to the 24GHz vehicle radar antenna. According to the actual needs in the project, the classification and design of the feed network of the array antenna are introduced. The electrical network has lower side lobe level and higher main lobe width than the traditional feed network. A feed network is designed by the Chebyshev synthesis method, which meets the needs of 24GHz vehicle radar antenna through simulation and testing.24GHz; low sidelobe; matching network; array antenna


In the frequency band greater than 10GHz, the PCB microstrip printed antenna has obvious advantages over other antennas such as waveguide slot antennas, lens antennas, and reflector antennas. The mature PCB processing technology can effectively control the production cost of the microstrip antenna. The multi-layer hybrid technology of the antenna board, the RF board and the low-frequency digital-analog circuit board also makes the entire RF system have a high degree of integration.


Thickness selection

The thickness of the microstrip antenna is mainly selected based on three factors: the working bandwidth of the microstrip antenna, the design of the feeding network and the antenna efficiency.
First, the PCB thickness affects the impedance bandwidth of the microstrip antenna. The smaller the PCB thickness and the larger the array scale, the smaller the antenna operating bandwidth.

Second, the thickness of the PCB determines the line width of the microstrip line in the impedance change section of the feeding network. For the RO4350B board with a thickness of 20 mil, the line width of the 50Ω and 100Ω microstrip lines are 1.13mm and 0.27mm, respectively, and the microstrip antenna corresponds to resonance at 24GHz. The length is about 3mm. If the impedance of a microstrip conversion section in the feed network is too small or too large, the microstrip line will be too wide or too narrow. If the microstrip line is too wide, it is easy to cause structural interference. will cause processing difficulties.


Antenna type

As shown in Figure 1, the microstrip array antenna is divided into parallel-fed array and serial-fed array according to the feeding mode. And the feeder line of the feeder array is long, which leads to a large loss introduced by the feeder network. For large arrays, the antenna efficiency is often limited, so a cross-feed array with simpler routing is generally selected. The series-fed array is a resonant antenna, and its operating bandwidth is smaller than that of the parallel-fed array, but the series-fed structure is easier to achieve weighted excitation.

Table 1 shows the series-fed microstrip array antennas of different scales designed by the author, all of which use RO4350B plate with a thickness of 20 mil. As can be seen from the data in the table, as the scale of the array becomes larger, the impedance bandwidth gradually decreases. The bandwidth is 1.2 GHz when there are 16 array elements, and only 0.75 GHz when there are 324 array elements. The FM bandwidth of the 24GHz radar that usually adopts the continuous wave system is less than 250MHz, so the impedance bandwidth of the cross-feed array can meet most of the system design requirements.


Third, the thickness of the dielectric affects the conductor loss of the microstrip line, which in turn affects the antenna efficiency. Based on the above factors, the author's design experience is to choose 10mil or 20mil thickness for small arrays, 20mil thickness for large arrays, and 10mil thickness for RF boards.

문의하기

Author:

Ms. Zoe Zhong

Phone/WhatsApp:

+8618617178558

인기 상품
You may also like
Related Categories

이 업체에게 이메일로 보내기

제목:
이메일:
메시지:

Your message must be betwwen 20-8000 characters

2010 년에 설립 된 Entnorson Antenna Co., Ltd는 커뮤니케이션 안테나의 연구, 개발, 판매 및 서비스에 종사하는 전문 회사입니다. Yetnorson은 2 g/3 g/4 g/wifi/TV 안테나와 다양한 RF 커넥터 및 안테나 케이블 어셈블리를 전문으로했습니다. 우리는 5 명의 엔지니어가있는 R & D 팀이 7 일 이내에 고객의 사양에 따라 프로젝트를 완료 할 수 있으며 귀하의 옵션을 위해 500 가지 이상의 현재 안테나 제품을 제공합니다. 그 동안 36 개의 제품 특허와 8 개의 상표가 있으며 ISO...
Newsletter
회사 주소
Room #101,201,301,5BLDG , No.4 of XinWuCun New Area ,Shabo community Maluan Street Pingshan District, Shenzhen ,Guangdong , China, Shenzhen, Guangdong China

Copyright © 2024 Yetnorson Antenna Co., Ltd.판권소유

Copyright © 2024 Yetnorson Antenna Co., Ltd.판권소유

We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

송신